01 of 07
Assemble the Ingredients and Equipment for Making Lye-Water
The first and most daunting step when making cold process soap at home is making the lye-water mixture that is needed. Don't do this until you are ready to proceed with making soap from scratch.
Lye is a caustic, dangerous chemical that can cause serious burns, but you can work with it safely if you take a few precautions and understand basic soap making safety procedures.
Chose a soap recipe and assemble all its ingredients and tools. Read through and understand each of the steps involved in... making a lye solution. Making lye-water is the first step in the soap making process; you need to be ready to proceed with the process after the lye-water is made. Your soap making recipe will list the specific ingredients, but most soaps require the same basic ingredients and equipment.
Making lye-water requires:
- lye flakes
- distilled water
- sugar or salt (optional if your recipe calls for it)
- safety goggles and gloves
- mason jar or plastic pitcher with lid
For a video version of these instructions, watch How to Make a Lye Solution for Soap Making video.Continue to 2 of 7 below.
02 of 07
Weigh the Water for the Lye Solution
In soap making, everything is measured by weight, even the liquids, which it why it is important to use an accurate scale and know how to zero it out.
Continue to 3 of 7 below.
- Put on the safety goggles and rubber gloves. Leave them on throughout the soap making process.
- Put the pitcher onto the scale and zero out the weight.
- Weigh the amount of distilled water called for in your soap recipe.
03 of 07
Weigh the Lye for the Lye Solution
Place a mason jar, plastic pitcher or other solid, safe container onto the scale and zero out the weight. Open the container of lye and gently shake out the amount you need for your recipe. As soon as you have the correct weight measure of lye, tightly close the lid on the lye container and put it aside in a safe place.
Be cautious that no stray beads or specks of lye fly up and stick to your gloves or shirt sleeves. This is more likely in dry climates or dry weather when there is a lot of static... cling. If this happens, stop and clean them off immediately.Continue to 4 of 7 below.
04 of 07
Add the Lye to the Water
If your recipe calls for adding sugar or salt to the lye water solution, add it to the water before you add the lye. Stir the water well to make sure the sugar or salt is completely dissolved and then move on to adding the lye to the water.
Slowly add the lye to the pitcher of water. Be careful to not make any splashes.
CAUTION: Always add the lye to the water, not the other way around. Adding the water to the lye can cause a volcano-like reaction in the pitcher. Do not breathe the fumes given... off by the mixture. Open windows or turn on fans while working.Continue to 5 of 7 below.
05 of 07
Stir the Lye and Water Mixture
Gently stir the mixture until the lye is completely dissolved.
The mixture will start to heat up and may even steam or make bubbling or boiling sounds. This is fine. Just continue to stir until the solution is thoroughly mixed.
Safety note: Look closely at the spoon you used to stir the solution when you pull it out. You can see a few drops of lye solution still on the spoon. Rinse the spoon off or put it into a pitcher of water so that those stray drops of lye don't come into contact with... something they shouldn't.Continue to 6 of 7 below.
06 of 07
Set the Lye in a Safe Place
After stirring, put the lid on the lye-water pitcher and set it in a safe place to cool. The lye is ready to use when it cools down to about 100 degrees Fahrenheit.
Even when the lye-water is placed aside, you still need to be safe.
Continue to 7 of 7 below.
- Don't put it in a place where pets or children can knock it over.
- If there are other people in the house, label the pitcher "DANGER-Lye Solution."
- The mixture is hot when you first mix it—often as much as 200 F. Don't place it near anything heat sensitive.
07 of 07
Take a Breath—You've Done It!
If there's any one thing that keeps people from trying cold process soap making, it's fear of dealing with lye. But look—you've done it and done it safely. As long as you always follow proper safety procedures, wear your goggles and gloves, and don't shortcut the steps, you should have no problems at all safely mixing lye to use in your soap making.
Now that the lye-water is made, the hard part is done. It is time to proceed with making the soap following your chosen recipe.