01 of 10
Tools, Equipment and Safety
Occasionally the need may arise where you would like to remove a coin from a third party grading service encapsulated coin holder such as a PCGS slab. It may be that you want to resubmit the coin to the grading service in hopes of achieving a higher grade or you would like to place it in a coin album in order to added to your collection. Regardless of the reason here is an easy way to remove the coin from its slab without damaging it.
First and foremost, the right tools are required in order to... safely remove the coin without damaging it nor injuring yourself. Use or purchase the following items:
- A soft cotton hand towel that is clean and free from dirt and grime.
- A gallon size Ziploc bag.
- Channellock 10-Inch End Cutting Nipper Pliers (Part #: 148-10)
I specifically like the Channellock brand of pliers because of their durability and accuracy when cracking out coins. Only the Channellock pliers use a knife and anvil style cutting edge to ensure perfect mating and superior cutting edge. I know these usually cost more than generic end nipping pliers but the money you will save by not ruining your first encapsulated coin will be well worth it. Also, the longer the handle length the less force you will need to exert in order to crack the plastic. Anything shorter than 10 inches and you risk losing control of the pliers and possibly damaging your coin.Continue to 2 of 10 below.
02 of 10
Hold the Coin Firmly but Don't Crack It Yet
It is important to work over the soft cotton towel in case you drop the coin at any time during this process. The first step is to grip the edge of the slab with the end cutting nipper pliers approximately where the insert that holds the coin on the inside of the slab is closest to the edge. Squeeze the players hard enough so the slab does not fall out but not too hard that you start to crack the plastic.Continue to 3 of 10 below.
03 of 10
Safety Is Job #1
While holding the PCGS coin slab with the end nipping pliers place the slab inside the plastic bag. This will prevent any plastic splinters or shards from flying across the room or getting embedded in your eye. Be careful not to drop the slab or have the position of pliers move while you do this.Continue to 4 of 10 below.
04 of 10
Make the First Crack
With your other hand firmly grasp the end nipping pliers with both hands. Gather some of the plastic bag under your hand in order to minimize the opening of the plastic bag. Firmly squeeze down on the pliers using an even motion until the plastic cracks. Carefully remove the pliers from the plastic bag without touching the part of the coin that is now exposed. Reach into the plastic bag and remove the plastic piece(s) that broke off. [CAUTION!] Exercise extreme caution because the cracked edges... of the plastic may be very sharp. If the peace did not separate from the slab, remove the slab and the piece together from the bag. Otherwise, remove the slab from the plastic bag last.Continue to 5 of 10 below.
05 of 10
The First Crack Is Complete
Although it is impossible to predict exactly how the slab will crack, more often than not the slab will crack diagonally from the point where the pliers made an impact to the bottom of the coin slab. If the piece did not separate from the slab, carefully slide the piece off the slab so you do not scratch the coin. [CAUTION!] Exercise caution because the cracked edges of the plastic may be extremely sharp.Continue to 6 of 10 below.
06 of 10
Get Ready for Crack #2
Using the end nipping pliers grasp the other side of the coin slab approximately halfway down where the inert plastic insert is closest to the edge of the slab. Use enough pressure so the slab does not fall away from the pliers and possibly damaged the exposed part of the coin.Continue to 7 of 10 below.
07 of 10
Carefully Make Crack #2
Carefully place the coin slab inside the plastic bag again. Be careful that you do not lose your grip and the coin slab falls away from the pliers. This may damaged the exposed part of the coin. While gripping the pliers with your other hand, gather some of the plastic bag in order to minimize the opening. Once again, firmly squeeze the pliers until the plastic cracks.Continue to 8 of 10 below.
08 of 10
Remove the Final Piece
Remove the slab and any remaining pieces from the plastic bag. Be careful that you do not scratch the coin with the pliers or the broken pieces. [CAUTION!] Once again, be careful because the cracked edges of the slab may be very sharp.Continue to 9 of 10 below.
09 of 10
Remove the Coin and Insert from the Slap
Carefully slide the coin and the inert plastic insert out of the slab. Be careful not to scrape the coin against the sharp edges of the broken encapsulated holder. Remember, the edges are sharp so be careful not to cut yourself.Continue to 10 of 10 below.
10 of 10
Remove the Coin from the Inert Plastic Holder
Now that the coin and the inert plastic insert has been removed from the slab, carefully slide the coin out of the inert plastic insert. It is best done with cotton or powder-free latex gloves. Your coin is now ready for re-submission or addition your coin collection.