01 of 05
Introduction to Building Your Own Tank
If you are up to giving it a try, building a fresh or saltwater DIY (Do It Yourself) aquarium from scratch can be fun, as well as challenging. From tips on working with glass, to providing a Materials List, pre-assembly instructions, and complete step-by-step instructions on how to construct a 55 gallon glass aquarium with 1/4 inch glass, here is everything you need to know about how to do-it-yourself.
Working With Glass Tips
Continue to 2 of 5 below.
- The aquariums we have built using these instructions measure 14 inches... high, 4 feet wide, and 14 inches deep, but are ideal for customizing smaller sizes as well. If you plan to build a taller or larger sized tank, refer to our aquarium glass thickness calculator.
- Plan ahead before cutting the glass by drawing a good schematic. If you do not feel comfortable with cutting glass, have a professional glazier cut and prepare the pieces for you.
- Use precise measurements, because this will insure a proper fit.
- We have always constructed our aquariums with the two end pieces of glass fit inside of the back and front panes, and the front, back, and two side panels set on top of the bottom base pane of glass.
See the Panel Placement Diagram Above
- Undoubtedly you will be putting a lighted hood on your tank, so design it accordingly. Do not put a solid glass cover on top of an aquarium, as this restricts the oxygen-carbon dioxide gas exchange efficiency, resulting in poor or inadequate aeration of the aquarium.
- Other common mistakes to avoid.
02 of 05
DIY Glass Aquarium Materials List
Aside from 1 bottom, 1 front, 1 back, and 2 end pieces of glass, you will need the following items to construct your aquarium.
Continue to 3 of 5 below.
- Single edged razor blades.
- A non-toxic 100% silicone sealant. We have used NAPA brand (part #765-1336) with good results for years, but we recommend All-Glass® Brand 100% Silicone Sealant or a similar type product.
- A roll of paper towels.
- A washable felt tip marker.
- A roll of duct tape.
- Some emery cloth or silicone carbide sandpaper.
- For a larger aquarium above... 30 gallons in size, we recommend installing at least one "support brace" at the center of the tank. This can be done by cutting a six inch wide piece of glass measured to fit to the "outside" edges of the front and back panels, then attach it into place with silicone. For extra strength you can pancake and glue two brace pieces together using silicone, or particularly for longer tanks, install two seperate brace pieces of glass equal distances from each end of the tank. Personally we prefer to use the multiple brace set-up, because this automatically builds in a place to sit one or two light strips/hoods on top of the tank. >> View Support Brace Placement Diagrams
03 of 05
Getting Ready to Assemble The DIY Glass Aquarium
BEFORE starting assembly of the aquarium you need to first get items ready for use, and learn about the following important points of construction.
Prepare the Cut Glass Panes
- Once the pieces of glass are cut, using the emery cloth or silicone carbide sandpaper, buff all the raw edges of the glass just enough to take off the sharpness.
- Clean all the glass pane joint areas and edges about 1/2 inch inward (any place where silicone will be applied) with acetone on a paper towel.
Prepare the Duct TapeCut... 16 strips of duct tape, about 5 inches long, and stick them to anything close by within easy reach that has a clean surface to it, and that the tape won't stick too much to, with at least half of the tape hanging down freely. If during assembly you run out of pieces of tape, before installing another panel, cut some more pieces. Tip: If at any time during construction you have trouble with the tape not sticking to the glass, just clean the area with some acetone on a paper towel and try again.
How To Properly Install the Glass PanesAs each pane is installed, as you go along you will be applying a thin but adequate solid line of silicone to each inside edge of all areas to be joined, then, at a slight forward angle, align and inset the piece of glass onto the bottom glass pane, and slowly tilting it upright, press it lightly, but firmly down into the silicone, fitting it solidly into position. DO NOT wipe off any excess silicone that might squeeze to the outside edges of the glass. This can be cleaned up or trimmed later on, once the silicone has fully cured.Continue to 4 of 5 below.
04 of 05
Tank Assembly Instructions - Installing Glass Panels1 ) After all your glass pieces are cut and prepared, lay or arrange the pieces out so you know which piece is going where. Once placement of the panes has been determined, to help keep track of where each piece goes (which edge or side of the glass pane is going to go up or down, inside or outside, etc.), mark them with words or directional arrows using a washable felt tip marker.
2 ) Take the bottom base piece of glass, place it on a flat, non-abrasive surface, then firmly press and stick 8... pieces of the duct tape (2 pieces on each side) to the glass from the bottom side with the sticky sides up (See Diagram View 1).
- Tip: This is easily done by lifting up the glass from each side just enough to stick the tape pieces in place.
3 ) Following the how to properly install the glass panes information from the previous page, and using our silicone application tips, install the front glass piece (See Diagram View 2). Once the front glass is in place, fold the 2 bottom pieces of duct tape upward and stick them to the front of the glass.
- Tip: This step is much easier to do with an assistant to hold the front glass pane upright and in place while you complete installation of the first side piece in the next step.
4 ) Using the same installation method, install the first side panel (See Diagram View 3), fold the 2 bottom pieces of duct tape upward and stick them to the front of the glass, and secure the side piece to the front piece of glass by wrapping 2 additional strips of duct tape around the corner from one side to the other (See Diagram Right End View Example.Continue to 5 of 5 below.
05 of 05
Assembly Instructions = Install Side & Back Panels5 ) Following the same procedure as above, install the other side piece, and finally the back panel.
6 ) With all the pieces in place and the tank constructed, run a thin but adequate solid line of silicone into the eight joint areas on the inside of the tank, then run your thumb over the silicone from one end to the other of each seam, preferably in one continuous motion, to smooth the silicone down and force it into the joint areas. (Install the "brace(s)" here, if adding one).
7 ) All...ow the silicone to cure for 24 hours.
8 ) Refill the tank with fresh water and allow it to sit for at least 12 hours, 24 is better. This gives you a good test period, and you will feel much more confident of success when you finally fill the tank with saltwater, put it all back together and add your inhabitants. If you find that something happened and you have a minor pin hole leak, you can fix this by following our simple instructions for repairing small leaks.