Embroidering on Wood

  • 01 of 07

    How to Embroider on Wood

    Embroidering on Wood
    Embroidering on Wood. © Mollie Johanson, Licensed to About.com

    When people see embroidery, even the simplest design, on a piece of wood, they always seem to be more impressed than they are when looking at complex, time consuming embroidery. Why is that? 

    I think it's because people have a basic understanding of how embroidery works: needle and thread passing through fabric. But how do you get a needle and thread through a piece of wood? 

    The answer is a lot easier than you'd expect. In fact, it's a lot like embroidering on paper, just with a...MORE little more effort. 

    Simple patterns are easier when stitching on wood, so it's best to start small, then work your way up to more complex designs. The biggest challenge to intricate work is that the holes you make can't be too close together, which means the stitches can't be too small or too close together.

    Now, let's get ready to stitch!

    Continue to 2 of 7 below.
  • 02 of 07

    Mark the Pattern

    Marking the Pattern
    Marking the Pattern. © Mollie Johanson, Licensed to About.com

    There are a couple ways that you can transfer your pattern onto the wood. For both, I'd recommend having a push pin handy to mark where the stitching holes will be. Plan to space the holes at least 1/8" apart, but 1/4" is safer.

    Marking Through Paper

    For simple patterns, print the design on regular paper and lay the paper on the wood. Use a push pin to make a small indent at each place where a stitch will need to go through. 

    In the photo shown above, I marked each end of a line segment...MORE and intersection. The geometric heart is from the free geometric Christmas pattern set.

    Take care to not let the paper pattern shift as you work. When you're finished, lift off the paper and you'll see the indents that mark out the pattern. You won't see the stitching lines, however, so refer to the pattern for that. 

    Marking with Transfer Paper

    The transfer paper method will work for just about any design. Place the transfer paper face down on the wood. Lay the printed pattern on top and trace over the design with a stylus or empty ball point pen.

    Lift away the papers and you'll see the outline of the pattern. From here, you may find it helpful to use a push pin to mark where each stitch hole should be.

    Continue to 3 of 7 below.
  • 03 of 07

    Drill Holes in Thick Wood

    Drilling Holes for Stitching
    Drilling Holes for Stitching. © Mollie Johanson, Licensed to About.com

    The craft wood section at hobby and craft stores offers a variety of products that are perfect for stitching on, as they are pretty much finished and smooth. Slices of tree branches (and even tree trunks) can be used too. 

    Depending on what kind of wood you'll be stitching on and the look you want to achieve, there are several ways to make the holes you'll stitch through. 

    Ideally, it's best to stitch through pieces that are 1" thick or less. 

    Wood Over 1/8" Thick

    A cordless...MORE drill with a 1/16-inch bit is the easiest way to make stitching holes. You will need to hold the piece firmly, while keeping the underside of the wood open so you don't make holes in things you don't want to. 

    Lay the board or wooden object on the edge of a counter (or a step as pictured above!) and hold it in place. Drill the stitching holes at each place where you have marked.

    If you don't have a drill, you can use a hammer and small nail. For this method, lay the marked piece on a piece of scrap wood or several layers of cardboard. Then hammer through at each marked point. Be careful to go through the wood, but not too far. Remove the nail and continue onto the next hole.

    Continue to 4 of 7 below.
  • 04 of 07

    Punch Holes for a Lacing Effect

    Punching Holes for Stitching
    Punching Holes for Stitching. © Mollie Johanson, Licensed to About.com

    Wood Up to 1/8" Thick with a Lacing Look

    For a bold effect with larger stitching holes, use a punching tool like a Crop-a-Dile to punch the holes. Just line up the marked indents with the punch.

    This method is is best for the simplest of designs, as the result will come out looking similar to lacing cards for kids. But don't let that stop you from making a project suitable for an adult. Just choose a modern design and stitch with thicker threads, yarn or ribbon!

    Continue to 5 of 7 below.
  • 05 of 07

    Poke Holes in Thin Wood

    Poking Holes for Stitching
    Poking Holes for Stitching. © Mollie Johanson, Licensed to About.com

    Balsa Wood

    Thin balsa wood is soft and a push pin will go right through the wood. For this method, place the balsa on an old magazine or newspaper, and then poke through each indent. Sometimes twisting and wiggling the pin helps.

    You may also be able to make the holes by holding the balsa in your hand, supporting it from behind with your fingers. Just take care not to poke your fingers or crack the balsa as it it fairly delicate. 

    Continue to 6 of 7 below.
  • 06 of 07

    Stitch Through the Wood

    Stitching Through Wood
    Stitching Through Wood. © Mollie Johanson, Licensed to About.com

    Choose your thread or number of strands based on how large the holes are, or consider making the holes larger. Conditioning your floss with Thread Heaven is also helpful, as it protects the thread some as you pull it through the rough surface. 

    Begin stitching through the pre-made holes. You may start with a knot, but often knots will pull right through, so it's best to use other starting methods.

    Flip the piece over to see the hole from the back, then flip it to the front to go back through...MORE the wood. Continue working this way, flipping it back and forth as you stitch.

    Continue to 7 of 7 below.
  • 07 of 07

    Finished Embroidery

    Embroidered Wooden Tag
    Embroidered Wooden Tag. © Mollie Johanson, Licensed to About.com

    When you've finished stitching the design, check to see if any markings are still showing. If they are, carefully remove them with a soft pencil eraser.

    If you want to cover the back of your work, you can use craft glue adhere a piece of fabric to the back. Just remember that it will be permanent!

    After you've stitched your first embroidered piece on wood, you'll be ready to move onto more complicated designs. But at any point along the way, you're sure to impress your friends with...MORE your new skill!