Make a Special Pillow with this Free Envelope Flap Pillow Pattern

  • 01 of 06

    Materials to Make an Envelope Flap Pillow

    Free sewing pattern and directions to make a pillow with an envelope flap
    Make an Envelope Flap Pillow. Debbie Colgrove, Licensed to About.com

    This pillow resembles a standard envelope. It makes wonderful eye candy in any room but is exceptional in a den or office situation. Experiment with colors and piping to make the design details stand out.

    Materials

    Continue to 2 of 6 below.
  • 02 of 06

    Make the Pattern for an Envelope Style Pillow and Cutting Out the Fabric

    Pattern for a Pillow with a Decorative Envelope Style Flap
    Pattern for a Pillow with a Decorative Envelope Style Flap. Debbie Colgrove, Licensed to About.com
    Your fabric could be measured and cut but since there are some angles, it is best to make the pattern on paper first.
    • Draw one rectangle that is 13 1/2" by 17". Use the 13 1/2" edge as a straight grain line. This will be the front part of the pillow that is under the envelope flap.
    • Draw a rectangle 10 1/2" by 17". Mark 3" from the bottom on both 10 1/2" sides. Find the center of the top 17" edge. Draw lines from the 3" mark to the center mark. Use the 3"...MORE edge as a straight grain line. This will be the lining piece for the flap of the pillow.
    • Draw a rectangle 17" by 21 inches. Mark 7 1/2" down from the top on each 21" edge. Find the center of the 17" top edge. Draw a line from each side marking to the top center marking. Use the 13 1/2" edge as a straight grain line. This will be the back and flap piece.
    • Use the final marked lines as the pattern pieces. (The black lines in the diagram.)
    Cutting:
    • Cut out one of each pattern piece. The facing can be cut out of a complimentary fabric if you are short on the pillow fabric.
    Note: All directions refer to a 1/2" seam allowance unless otherwise noted.
    Continue to 3 of 6 below.
  • 03 of 06

    Piping

    Piping on an Envelope Style Pillow
    Piping on the Envelope Style Pillow. Debbie Colgrove, Licensed to About.com

    Using a 1/2" seam allowance, sew piping to the edges of the back and flap piece. Clip the corners to allow the piping to lay flat on the fabric. (How to Cover Your Own Cording to Make Piping | How to End Continuous Piping)

    Continue to 4 of 6 below.
  • 04 of 06

    Hem Edges

    Hemming edges while making an envelope pillow
    Hemming Edges. Debbie Colgrove, Licensed to About.com

    On the flap lining

    • Sew a straight row of stitching 1/4" from the edge of the fabric on the 17" edge.
    • Turn under and press,so the wrong sides are touching, using the row of stitching as a fold line.
    • Turn under again to enclose the raw edge.
    • Sew a closely to the inside folded edge as possible to hold the hem in place on the flap.

    On the front bottom panel

    • Sew a straight row of stitching 1/4" from the edge of the fabric on the top 17" edge.
    • Turn under and press,so the wrong sides are...MORE touching, using the row of stitching as a fold line.
    • Turn under again to enclose the raw edge.
    • Sew a closely to the inside folded edge as possible to hold the hem in place on the inside of the front bottom panel.
    Continue to 5 of 6 below.
  • 05 of 06

    Assembling the Pieces

    Assembling the Pieces of an Envelope Style Pillow
    Assembling the Pieces of an Envelope Style Pillow. Debbie Colgrove, Licensed to About.com
    • Lay the back and flap piece right side up on a flat surface.
    • Lay the front bottom piece, right side down on top of the bottom of the back and flap piece, aligning the side and bottom edges.
    • Lay the flap lining, right sides down on the top section of the back and flap, aligning the edges.
    • Pin all pieces in place.
    Continue to 6 of 6 below.
  • 06 of 06

    Sewing and Finishing

    Sew the seams and apply a seam finish.
    Sewing the Seams. Debbie Colgrove, Licensed to About.com