How to Install Paver Edging

Pavers in a circular pattern
Ulga / Getty Images
Overview
  • Working Time: 60 mins
  • Total Time: 40 hrs
  • Yield: 10 x 10 patio
  • Skill Level: Intermediate
  • Estimated Cost: $80 to $100

Paver edging is a rigid plastic building material used to create boundaries for patios or walkways built with sand-set bricks or concrete pavers. When building a paved surface, the paver edging is laid down after the compactible gravel base and serves as a boundary to keep the sand layer in place and facilitate paver installation. It also extends the life of the patio or walkway by the sand base from washing away over time.

Made from recycled vinyl or another rigid plastic, paver edging is similar to the flexible plastic edging used to create boundaries for lawns and planting areas, but it is a heavier duty, contractor-grade product. Rather than being sold in long rolls, paver edging comes in rigid 6-foot lengths that are held in place with nylon-coated spikes that are driven through the edging and into the ground. If curves are desired, connecting tabs in the edging can be cut to allow it to bend into gentle curves.

When the patio of finished and surrounded by lawn or planting beds, the paver edging disappears from view. While sand-set paver patios are frequently built without paver edging, a patio is usually more stable and long-lasting when these edging strips are installed and properly anchored.

Using Paver Edging in Construction

Paver edging is always installed as part of a larger project, building a sand-set paver patio or laying a brick walkway. After the patio is laid out and a gravel base is installed, leveled, and compacted, the lengths of paver edging are installed over the gravel base to form a boundary for the paver sand that will be spread out and leveled before brick or stone pavers are laid.

Occasionally, contractors or DIYers choose to install the edging after the patio pavers are laid, tucking the edging under the bricks before anchoring it to the ground. Although this is not technically "correct," it makes for a somewhat more forgiving building process, since anchoring the paver edging first before requires a great deal of layout precision if you want to avoid cutting bricks at the edges.

What You'll Need

Equipment / Tools

  • Hand saw or handheld power saw
  • Hammer or hand maul

Materials

  • 8 Paver edging
  • 28 8-inch nylon spikes

Instructions

  1. Begin Patio/ Walkway Construction

    Complete the preliminary steps of patio or walkway construction by laying out the area with stakes and layout strings, excavating the building site, and laying and compacting a gravel base. Make sure to refasten layout strings and measure them to make sure they precisely outline the finished patio or walkway.

  2. Position the Paver Edging

    Place lengths of paver edging in the desired location, taking pains to make sure they are carefully aligned with the layout strings. Ideally, the paver edging should be installed to perfectly match the desired size and shape of the patio or walkway. Use a hand saw or handheld power saw, such as a jig saw, where you need to cut partial pieces of edging.

  3. Form Curves

    Where the patio will have curved edges, the edging can be shaped to conform by cutting the connecting tabs along the edge of the edging. This removes the rigidity of the edging and allows the vertical flanges to bend to make curves. Some care is needed to hold the edging to the desired shape as you anchor it with spikes. A helper can be useful for this step.

  4. Anchor the Edging

    Drive 8-inch nylon spikes through the holes on the edging and into the ground. Drive spikes at the ends of each length of edging, and about every 18 inches in between. Curves will require more spikes. Be careful while driving the spikes with a hammer, as they can sometimes snap.

  5. Complete the Patio or Walkway

    Now, return to patio/walkway construction by laying a sand bed, setting the bricks or pavers, and filling cracks with paver sand.

    As you work across the patio or walkway, you may find that the last pieces of paver edging need to be adjusted slightly if you want to avoid cutting pavers. This is a fairly easy matter of prying up the spikes, moving the edging, then redriving the spikes.

  6. Finish the Edges

    After the patio or walkway is completed, the exposed edges where the paver edging is visible can be covered up with pieces of sod if the patio adjoins the lawn, or with soil and mulch if it adjoins a planting bed.