How to Make an Ice Candle

  • 01 of 10

    How to Make an Ice Candle

    Setup for Ice Candle
    Setup for Ice Candle. David Fisher

    I bet most of us made an ice candle some time in elementary school - using an empty cardboard milk container and some string for the wick. This ice candle project is a bit more involved than that - but still a fun, surprising and easy project.

    For this project you'll need:

    • A mold of some sort - yes, you can even use a cardboard milk container - I'm using a pillar candle mold
    • A relatively high melt point wax - a pillar blend, or a hurricane blend - I'm using IGI 1014 - but there are...MORE different types of wax you can use.
    • A candle to use as the "core" - I'm using a ball candle and a standard taper
    • Color and/or fragrance as desired
    • Ice, chopped into small pieces/chunks
    • A basic understanding of Candle Safety
    Continue to 2 of 10 below.
  • 02 of 10

    Prepare the Molds for the Ice Candle

    Mold Sealer
    Mold Sealer. David Fisher

    Depending on what sort of mold you're using will determine what sort of preparation you have to do.

    If you're just using a milk container, just make sure that it's clean and intact. If, like I am here, you're using a regular candle mold, be sure to seal up the wick hole (if it has one) with mold sealer. Make sure to press it down well and evenly. You want to make sure that the candle sits level on the counter.

    Start your wax melting. You want it to be about 200 degrees when you...MORE pour it!

    Continue to 3 of 10 below.
  • 03 of 10

    Setting the Core Candles into the Mold

    Taper In Pillar Mold
    Taper in Pillar Mold. David Fisher

    Next, set the candle you are using as the "core" into the mold. For this project, I'm using a standard taper candle in a tall pillar mold, and a ball candle in a shorter pillar mold.

    If you're using a taper, you want the very top of the wick to just reach the top of the mold. If your taper is too long (as mine is here), you'll want to cut a bit off of the bottom. Otherwise (like I had to do with this one), you either have to cut or melt the tip off. Here's a picture of the...MORE candle with the top melted off.

    Continue to 4 of 10 below.
  • 04 of 10

    Setting the Core Candle - Part Two

    Ball Candle
    Ball Candle in Pillar Mold. David Fisher

    Here's the ball mold in the shorter pillar mold.

    Continue to 5 of 10 below.
  • 05 of 10

    Pack the Molds with Ice

    Pouring Ice
    Pouring Ice. David Fisher

    Next, holding the core candle firmly, pour chunks of ice into the mold. The size of your ice chunks will determine the character of your final candle. I used fairly small ice chunks in the small pillar mold with the ball candle and larger chunks in the tall pillar mold with the taper candle.

    Continue to 6 of 10 below.
  • 06 of 10

    Pour the Wax into the Mold Prepared for the Ice Candle

    Pouring the Wax
    Pouring the Wax. David Fisher

    When your wax has reached about 200 degrees, add any color or fragrance you desire (I usually don't add fragrance to ice candles), and get ready to pour.

    It's a good idea to have a little extra eye, hand, and counter protection when pouring ice candles. There's an extra chance for sputters, spills and splashes.Slowly pour the hot wax into the mold, bringing it just over the top of the core candle. (Or, in the case of the taper that I didn't trim, to the top of the mold.)

    Continue to 7 of 10 below.
  • 07 of 10

    Setting the Ice Candles Aside to Cool

    Cooling Candle
    Cooling Candle. David Fisher

    After you've poured the candles, set them aside to cool. Since you've got them half-filled with ice, they'll cool quickly - but it's still a good idea to let them sit for an hour or so.

    As you can see here, I misjudged the height of the taper a bit...I'll either cut that little tip off or just melt it down. It's easier to just cut a bit off of the bottom of the candle before you put it into the mold, though.

    Here's a picture of the green candle after I melted the top...MORE off.

    Continue to 8 of 10 below.
  • 08 of 10

    Unmold and Drain

    Draining the Candle
    Unmold and Drain. David Fisher

    Once the candles have cooled, gently pour out the water (melted ice) and unmold the candle. Gently shake out the excess water and set them on a towel to dry. Let them dry completely before lighting!

    Continue to 9 of 10 below.
  • 09 of 10

    Enjoy Your Ice Candles!

    Ice Candle Glow
    Ice Candle Glow. David Fisher

    After they've dried, they're ready to light and enjoy. Ice candles can be a bit unpredictable to burn, though. Sometimes the chunky edges will fall off or melt unevenly. Just be sure to burn it on a safe plate. When the flame burns down into the center of the candle, it gives off a lovely glow through the openings in the wax.

    Continue to 10 of 10 below.
  • 10 of 10

    Ice Candle Making Variations

    Ice Candles
    Ice Candles. David Fisher

    There are lots of variations you can do with ice candles.

    • First and foremost, you can vary the mold and core candle you use. Tall, short, different colors, different shapes.
    • Varying the size of your ice chunks...
    • Pouring different color waxes into the mold (from several cans or melt pots) can give you a marbled/tie-dye look
    • Add glitter or color to the wax

    Just use your imagination and enjoy!