How to Make Perfect Box Joints

Carpenter measuring wooden plank
Guido Cavallini / Getty Images
  • 01 of 10

    Make Perfect Box Joints with this Box Joint Jig

    Building a Box Joint Jig
    Building a Box Joint Jig. (c)2008 Chris Baylor licensed to About.com, Inc.

    Box joints are a strong, sturdy and attractive alternative to dovetail joints. While a through dovetail joint is stronger than a box joint, it's also more complicated to create. However, as you'll see in the following steps, a perfectly-fitting, clean box joint is easy to create very quickly with a simple box joint jig for your table saw.

    In this set of free woodworking plans, learn how to build a box joint jig that can be used over and over again to create box joints.

    Difficulty Level

    • Woodworking:...MORE Easy
    • Finishing: none required

    Time to Complete

    • 15 minutes

    Recommended Tools

    Materials Needed

    • 1 - 5-1/2" x 10" piece of 1/2" or 3/4" plywood or 1x6
    • 3 - 1-1/4" Wood Screws
    • Woodworking Glue

    To begin making your box joint jig, you'll need to determine what width you'll want each of the fingers of the joint to be. For instance, if you want to make your fingers 1/2" wide, start by ripping a strip of stock 1/2" x 1/2" by at least four inches long. Also, cut a piece of 1x6 (or plywood) cut to a finished size of 5-1/2" x 10" as shown in the picture above.

    Continue to 2 of 10 below.
  • 02 of 10

    Install the Stacked Dado Blade Set

    Setting up the Stacked Dado Blade Set
    Setting up the Stacked Dado Blade Set. (c) 2008 Chris Baylor licensed to About.com, Inc.

    Once you've cut the two wooden pieces for the jig, you'll need to install your stacked dado blade set in your table saw. Position enough chippers in between the two outer blades so that the final width of cut will match the desired width of the box joint fingers you determined in the previous step.

    Continue to 3 of 10 below.
  • 03 of 10

    Attach the Board to the Miter Gauge

    Attach the Board to the Miter Gauge
    Attach the Board to the Miter Gauge. (c)2008 Chris Baylor licensed to About.com, Inc.

    Next, attach the board to your table saw's miter gauge, as shown in the picture above. Slip the miter gauge into the miter slot to the left of the saw blade and check to see that the miter gauge is set to 90-degrees (perpendicular to the saw blade). Then, position the board on one of the long edges, against the miter gauge, making certain that the board extends at least 1/2" past the stacked dado blade.

    Use your cordless drill or corded power drill to drive a pair of wood screws through the slots...MORE or holes in the miter gauge, and into the block of wood. Be certain that the screws are short enough that the point doesn't poke through the face of the board.

    Continue to 4 of 10 below.
  • 04 of 10

    Cut a Notch in the Backer Board

    Cut the First Notch in the Jig
    Cut the First Notch in the Jig. (c)2008 Chris Baylor licensed to About.com, Inc.

    With the board attached to your table saw's miter gauge, the next step will be to cut a notch on the board to accommodate a spacer block.

    If the strip that you cut in step 1 was 1/2" wide by 1/2" high, then you'll need to adjust the height of your dado blade to 1/2" above the top of the table saw. Then, turn on the motor and slide the miter gauge forward, guiding the backer board all the way through the blade, cutting a 1/2" x 1/2" notch on the board. Slide the gauge back...MORE toward your body (clearing the blade again) and then turn off the saw.

    Continue to 5 of 10 below.
  • 05 of 10

    Attach the Spacer Block

    Attach the Spacer Block to the Backer Board
    Attaching the Spacer Block to the Backer Board. (c)2008 Chris Baylor licensed to About.com, Inc.

    After the first notch has been cut in the backer board, insert the spacer block through the notch. It should fit snugly without raising the backer board off of the surface of the table saw.

    Slide the spacer block so that the end is two inches past the front face of the backer board, and make a pencil mark on the spacer block against the back side of the backer board. Cut the spacer block at this cut line. Retain both halves of the piece that you cut, as you'll need both pieces.

    Next, remove the...MORE miter gauge from the table saw and turn it upside-down, exposing the bottom side of the backer board. Place a small amount of glue into the notch and position the spacer block in the notch so that the cut you just made is flush with the back side. Pre-drill and countersink a screw attaching this spacer block to the backer board as shown in the image above.

    Continue to 6 of 10 below.
  • 06 of 10

    Adjust the Box Joint Jig

    Adjusting the Box Joint Jig
    Adjusting the Box Joint Jig. (c)2008 Chris Baylor licensed to About.com, Inc.

    With the spacer block installed, re-position the miter gauge into the left slot of the table saw. Then, remove the two screws that mounted the jig to the miter gauge.

    Slide the box joint jig a bit to the right, using the remaining portion of the spacer block that you cut off in the previous step to adjust the width of the jig. See the image above for clarification.

    With the jig positioned so that the installed spacer block is now precisely one box joint finger's width past the dado blade,...MORE re-attach the backer block to the miter gauge using the two screws you just removed.

    The box joint jig is now complete. In the coming steps, you'll learn how to use this jig to cut perfect box joint.

    Continue to 7 of 10 below.
  • 07 of 10

    Begin to Cut the Box Joint

    Begin to Cut the Box Joint
    Begin to Cut the Box Joint. (c)2008 Chris Baylor licensed to About.com, Inc.

    To begin cutting a box joint, you'll need the two pieces of stock into which you'll be cutting the joint. Typically, these two pieces of stock will be the same thickness and width, as in two corresponding sides of a drawer box.

    Before making the first cut, you'll need to adjust the depth of the stacked dado blade on the table saw to match the thickness of the stock being cut. For instance, if you built the jig to have 1/2" wide fingers, but the boards being cut are 3/4" thick,...MORE you'll need to raise the blade to match the thickness of the board.

    To make the first cut, position the board on the edge so that the end edge of the board that will be cut is flat on the table. Slide the board to the right so that it butts up against the spacer block, leaving the edge flat against the table. After verifying that the board is extending upward square to the table saw the face, clamp the board against the jig with a small woodworking clamp. Notice the picture above as an example.

    Turn on the table saw and push the jig all the way through the stacked dado blade. This first cut will cut a new notch in the jig in addition to cutting the board. After the jig clears the blade completely, pull the jig back toward your body past the blade again and turn off the saw.

    TIP: For good measure, add about 1/64" of an inch to the height of the blade so that when the box joint is assembled, the fingers will be slightly proud of the mating surface, ensuring a complete joint. This slight extension can be sanded after the final assembly of the box joint.

    Continue to 8 of 10 below.
  • 08 of 10

    Adjust the Board on the Jig

    Re-adjusting the Board for the Next Cut
    Re-adjusting the Board for the Next Cut. (c)2008 Chris Baylor licensed to About.com, Inc.

    After the first finger has been cut, remove the clamp from the jig and re-position the board so that the newly-cut notch slides onto the spacer block on the jig. Check to see that the edge of the board is flush with the table and re-clamp the board to the jig, as shown in the picture above.

    Cut the second notch in the same manner that you cut the first.

    Remove the clamp, adjust the board so that the second notch now slides onto the spacer, re-clamp and cut the third notch. Continue this procedure...MORE until all of the needed finger notches on this edge of the board have been cut. While your last cut might not be a complete cut or the last finger may not be of a full 1/2" width, just remember that when you run out of the board, you've finished cutting notches.

    Continue to 9 of 10 below.
  • 09 of 10

    Cut the Box Joint Fingers in the Second Board

    Positioning the Second Board on the Jig
    Positioning the Second Board on the Box Joint Jig. (c)2008 Chris Baylor licensed to About.com, Inc.

    The procedure for making the first notch in the second, corresponding board is different than the procedure used to cut the first. If you cut the second board the same way as you cut the first, the edges of the board won't match up when you assemble the joint.

    To align the second board, place the edge of the board against the table and the face against the jig's backer board (as before), but this time, slide the board to the right so that the top edge of the board just barely covers the notch...MORE in the jig. Notice in the picture above, that the board just barely covers up the notch, which is 1/2" away from the spacer block.

    Clamp the board to the backer board and cut the first notch. This notch should be much like a rabbit, where the full width of the notch matches the edge of the board.

    After completing this first notch, remove the clamp, slide the board to the right so that the first notch is positioned over the spacer block. Re-clamp the board to the jig and cut the second notch. Continue this procedure as before until all of the finger notches have been cut.

    Continue to 10 of 10 below.
  • 10 of 10

    Assembling the Box Joint

    Assembling the Completed Box Joint
    Assembling the Completed Box Joint. (c)2008 Chris Baylor licensed to About.com, Inc.

    With the box joint fingers on both boards cut, check to see how well you did by dry assembling the box joint. The joint should fit snugly but the fingers should not be too tight, and the fingers should extend just slightly past the outside face of the corresponding board.

    When it's time for final assembly, simply apply a small amount of woodworking glue on all faces of the box joints on both boards, assemble the joint and clamp the boards in place.