If your humidifier fails to run because it is not getting water (provided the water tap is open), the problem can usually be traced to one of two reasons. The problem may lie with the solenoid—an electrically activated valve that opens the water flow when it receives an impulse from the humidistat. Or, the problem may lie with the humidistat—a switch that senses and measures air humidity and sends the "open" signal to the solenoid valve when the air humidity is low.
It's more likely that the problem is caused by a solenoid valve that has stuck shut. This can happen even if the humidistat is sending voltage to the solenoid, and a faulty solenoid will shut off the water cause the humidifier to stop operating. But before replacing the solenoid, you must test to verify where the problem lies.
Equipment / Tools
- Adjustable wrench
- Plumber's tape
- New solenoid (specific to your brand and model number)
Test the Solenoid
The solenoid is an electrically actuated valve that allows water to flow to the humidifier and is controlled by the humidistat—a sensor that operates like a temperature thermostat but is designed to sense humidity. For example, when the humidity level hits a certain point, the humidistat switch will open or close an electrical circuit (usually 24 volts) that provides current to the solenoid, which subsequently opens or closes water flow to the humidifier. The humidistat will only send voltage to the solenoid when the furnace is running and moving air.
You can use a multimeter to determine if the solenoid is faulty.
First, temporarily set the thermostat higher than its current setting, so that it calls for heat. With the furnace running, attach one multimeter probe to one of the wiring connections that goes from the humidistat to the solenoid, then attach the other probe to the other wiring connection that links the humidistat to the solenoid.
In our example, the humidistat is installed on the outside of the furnace’s return duct, and its humidity measuring sensor is in the return air stream. To check the operation of the humidistat and solenoid:
Turn the humidistat to a very low setting or to “off.” The multimeter should register no voltage. Then, turn the humidistat to a very high setting, such as 80 percent relative humidity, or until you hear a “click” sound. The multimeter should register about 24 volts if the humidistat is functioning correctly. If it does not register voltage, then you have a problem with the humidistat.
If you show 24 volts at the connection from the humidistat to the solenoid, then the humidistat is operating correctly and it is sending the proper voltage to the solenoid. But if the humidistat is operating correctly (24 volts is displayed) and the solenoid still is not allowing water to flow to the humidifier, then this means that the solenoid is defective and needs to be replaced.
Turn off the Water Supply
The first step in replacing the humidifier solenoid is to turn off the water supply to the solenoid valve.
Trace the water supply line from the bottom of the solenoid to its shut-off point This is often a saddle valve on a larger cold water supply pipe. Turn this small valve clockwise until it is fully seated and in the closed position.
Remove Electrical and Water Connections
The solenoid will have two water tubes attached to it. One is a water supply tube, and the other is a water inlet tube that runs to the top of the humidifier. There are also two low-voltage electrical connections to the solenoid.
First, turn off power to the furnace. Disconnect the wire connections from the solenoid to the humidistat.
Using an adjustable wrench, loosen and remove the female threaded compression nut on the compression union that secures the water supply tube to the solenoid. Repeat the process for the compression nut that attaches the water inlet tube to the solenoid.
Remove the Defective Solenoid
The solenoid is held in place with screws or posts. Remove the solenoid from the humidifier by unscrewing the knurled knobs from the screw posts.
Attach the New Solenoid to the Humidifier
Once you obtain a replacement solenoid for your make and model of humidifier, the next step is to attach it to the humidifier body, by threading the knurled knobs onto the mounting posts. Make sure you have the solenoid properly positioned by aligning the threaded union male ends of the solenoid with their matching union nuts on the water lines to which they attach.
Attach Water Lines to the Solenoid
Wrap the male threads of the union body with plumber's tape by tightly wrapping two to three complete wraps of the tape around the threads in the same “tightening” direction as the threads (clockwise as you look at the opening).
Carefully seat the copper water inlet tube (bottom tube in photo) from the water shut-off valve into the solenoid, and tighten the compression nut snugly.
Make sure one end of the water feed tube (top tube in photo) is in position at the top of the humidifier trough, then carefully set the copper water inlet feed line from the humidifier into the solenoid, and again tighten the compression nut snugly.
Turn the water supply back on by turning the valve handle counter-clockwise until fully open. Check for leaks.
Reattach the Electrical Connections
Connect the wire leads on the new 24-volt solenoid to the humidistat wiring by twisting the wires together and securing them with wire nuts.
Complete and Test the Installation
Your installation is now complete. While the furnace is running, temporarily turn the humidistat up to about 80 percent, or until you hear it click on. Water should now be flowing into the humidifier. Wait a minute or two and then check the humidifier drain to make sure water is flowing through the humidifier. If you see drips coming out of the drain or the end of the humidifier drain pipe, your installation is successful.