How to Install a Dalskar Bathroom Faucet From Ikea

  • 01 of 09

    Introduction

    Like much of the merchandise from Ikea, the Dalskar bathroom faucet is designed for easy installation, but unfortunately, the instructions are in picture form only. This tutorial will fill in some of the blanks and is designed to be used alongside the manufacturer's photo instructions. 

    Difficulty Level

    • Easy

    Tools and Materials You Will Need

    • Dalskar bathroom faucet
    • Pipe-joint compound
    • Channel-type pliers

    There are very few parts of the Dalskar bathroom faucet kit. It even comes with the tool to tighten the faucet, so no tools are required besides what they give you. Even the supply tubes are already built into the faucet, so connecting them is very easy.

    Continue to 2 of 9 below.
  • 02 of 09

    Set the Faucet In the Sink

    First, place the O-ring on the base of the faucet into the grove. The O-ring is what will keep water from getting in under the faucet body. No plumber's putty is required under the faucet. When you set the faucet onto the sink, make sure the body is centered within the sinkhole.

    Continue to 3 of 9 below.
  • 03 of 09

    Secure the Faucet to the Sink

    Next, from underneath the sink, place the U-shaped rubber gasket over the bottom of the faucet and up against the sink surface, followed by the U-shaped metal bracket. Next, come the brass nuts that hold the U-shaped bracket. Tighten the nuts with the provided tool, making sure that the faucet is centered correctly before fully tightening the faucet into place. 

    Continue to 4 of 9 below.
  • 04 of 09

    Maintenance Parts of the Dalskar Faucet

    After installing the faucet, you will notice a few extra parts. These are extras provided for future maintenance and service, so do not throw them away. In the kit, there is an aerator removal tool that will let you take the aerator off to clean it. Also, there is an Allen key used to remove or tighten the handle. Once the button is popped out of the back of the handle, the Allen key can be used.

    Continue to 5 of 9 below.
  • 05 of 09

    Drain Assembly for the Dalskar Faucet

    The faucet also comes with a drain assembly, featuring a simple push-pull pop-up assembly. 

    The first step is to peel off the sticky paper part of the foam gasket and stick it under the top flange of the drain assembly. (Instead of the sticky foam gasket, you can also use plumber's putty.)

    Continue to 6 of 9 below.
  • 06 of 09

    Apply Sealant on the Pop-Up Gasket

    Next, apply a thin coat of pipe joint compound on the rubber gasket to help it seal the rubber. This step is optional but will help ensure a tight seal.

    Continue to 7 of 9 below.
  • 07 of 09

    Fasten the Pop-Up Drain

    The bolt will go down from the top flange and tighten into the assembly from the top of the sink. Use the Allen key provided to tighten the top flange all the way down. Make sure that the flange is centered in the drain opening before tightening it down snug. Now, you can drop the stopper into place.

    Continue to 8 of 9 below.
  • 08 of 09

    Install the Tailpiece

    The last piece to install is the tailpiece attached to the bottom of the drain assembly. Make sure the rubber gasket is inside the tailpiece before screwing it onto the drain assembly. Hand-tighten the tailpiece; it will now resemble any other 1 1/4" tailpiece from a bathroom faucet. 

    Continue to 9 of 9 below.
  • 09 of 09

    Finish the Hookups

    Now you can connect the drain to the P-trap using the same methods as for any bathroom sink. Connect the faucet supply tubes to the shut-off valves under the sink.

    Your faucet installation is complete.