How to Install an Over-The-Range Microwave

Kitchen
karamysh / Getty Images
Overview
  • Working Time: 4 hrs
  • Total Time: 4 hrs
  • Skill Level: Intermediate
  • Estimated Cost: $300 to $800 (including oven)

Installing an over-the-range microwave oven is often easier than you think. If you are simply replacing an existing vent hood or older microwave with a new oven, you can install it easily enough with common tools. You will, though, probably need a helper, as an extra set of hands is essential.

Although the project seems a little intimidating, an over-the-range microwave oven comes packaged with the mounting brackets, templates, and instructions to make it relatively easy to install your appliance. If the available space is the right size—with propertly spaced adjoining cabinets and an overhead cabinet to contain the ductwork connections—then installing an over-the-range microwave requires just a few hours of work.

In its simplest form, the project involves installing a mounting bracket on the back wall, drilling access holes in the upper cabinet through which to feed the electrical cord and vent duct, hooking the oven onto the mounting bracket, then bolting the oven in place through the bottom of the upper cabinet. Attach the ductwork and plug in the oven, and you're done. But as with many home improvement projects, it is sometimes more complicated than that.

When to Call in a Pro

The installation will be relatively easy if there is access to an electrical outlet in the space above or behind the microwave, and if there is an existing vent duct running through the side wall or up through the roof. If that's not the case, then you may find the project complicated by the need to install a new electrical circuit and to run new ductwork and an exterior vent. At this point, the project shifts from an intermediate-level to an advanced-level project. If your skills are not up to it, it might be best to call in a professional for the electrical work, the vent work, or both.

Another possible complication is if substantial cabinetry work is needed, such as installing an upper cabinet to mount the oven and run the ductwork and the electrical cord. Again, this turns an intermediate project into a more advanced one, and it can turn a few hours of work into a weekend project.

Install Over the Range Microwave Tools
Lee Wallender

Many DIYers already own most of the tools needed for this project. At most, you'll need to buy a few tools, none of them very expensive.

What You'll Need

Equipment / Tools

  • Tape measure
  • Stud finder
  • Carpenter's pencil
  • Level
  • Jigsaw
  • Eye protection
  • Phillips screwdriver
  • Drill and bits
  • Ratchet wrench and sockets
  • Tin snips (optional if installing a vent)

Materials

  • Masking tape
  • Vent collar or other vent fittings (as needed)
  • Above-the-range microwave oven
  • Metal foil tape
  • Sheet metal screws (as needed)

Instructions

  1. Find the Studs

    The mounting strip that supports the back of the microwave needs to be secured to wall studs, not simply the wallboard. Begin by using a stud finder to locate the studs in the space below the upper cabinet. Then, use a level to extend the lines downward on the wall, marking them with a pencil.

    Find the Studs
    Lee Wallender

  2. Apply Paper Template on Wall

    Your microwave should have two paper templates: one to apply against the back wall, another to tape to the bottom of the upper cabinet. Apply the wall template to the wall with masking tape.

    Apply Paper Template
    Lee Wallender

  3. Apply the Paper Template to the Cabinets, Drill Holes

    After the second template to the bottom of the upper cabinet. This template will show you where to drill holes for power cords and venting. Drill these holes at the indicated locations with a spade bit. You will also drill holes for the oven's mounting bolts, at the indicated locations.

    Microwave Template on Upper Cabinets
    Lee Wallender
  4. Cut Openings for the Vent

    The location for your vent will depend on if the existing vent runs up through the roof, or through the back wall behind the oven. Use a jigsaw to cut an opening in either the back wall template or the bottom of the upper cabinet, depending on how the vent and ductwork is configured.

    • Note: You may need to add a vent collar or transition fitting or make other adjustments to the oven's venting feature before lifting the oven up into place.
  5. Install the Mounting Bracket

    Position and mount the metal mounting bracket on the back wall, following manufacturer's directions. Ideally, the strip should be anchored at stud locations. Where it is not possible to anchor to at least two studs, the manufacturer may provide instructions for using alternate wall anchors to attach the bracket. But it is important for the strip to be attached to at least one wall stud, preferably two.

    Install Microwave Mounting Plate
    Lee Wallender

    .

  6. Position the Microwave Oven

    With the assistance of a helper, lift the microwave into place, feeding the electrical cord up through the drilled hole in the upper cabinet. Have your helper hold the bulk of the weight while you reach around back and hook the oven's slots over the the tabs on the metal mounting bracket. Have your helper hold the oven up against the upper cabinet as you quickly move to the next step.

    Lift Microwave into Place
    Lee Wallender
  7. Attach the Top Mounting Bolts

    Your microwave's installation kit should come with self-aligning mounting bolts. With your partner still steadying the microwave, go above into the upper cabinet and thread the bolts down through the drilled holes and into the chassis of the oven. As soon as they are threaded, your helper can let go. Tighten screws the rest of the way with a wrench. As you tighten, use a level to make sure the oven is perfectly horizontal.

    Tighten Microwave Upper Screws
    Lee Wallender
  8. Connect the Duct

    If your microwave is being vented through ductwork, connect the oven's vent outlet to the ductwork. Some form of transition fitting may be needed; if necessary, use tin snips and metal screws to shape and secure the pieces together. Seal all joints with metal tape. (Do not use standard duct tape for this.)

    Plug in the oven and test its operation.

    Over the Range Microwave Connect Duct
    Lee Wallender