Make a Simple Dollhouse Scale Window or Storage Box With Rabbet Joints

  • 01 of 10

    Make a Simple Dollhouse Scale Window or Storage Box With Rabbet Joints

    Dolls house plants fill the interior of a painted 1:12 scale window box with heart cutouts.
    Dolls house scale plants fill the interior of this window box with heart cutouts. The box could also be used to hold a set of small planted pots. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    Wooden crates and storage boxes are a staple for many dolls house scenes. Practise making them by making these simple decorative boxes with rabbet joint ends. The joints are made with a simple flat file, and files are also used to help form decorative heart cutouts in the box sides. As shown here the box is used for a planter, but it can also hold pots of dollhouse plants, scale patterns, magazines or cd's. If you change the size, the same techniques will make beer and milk crates, or...MORE storage boxes for all kinds of miniatures.

    The rabbet joint is one step up from a butt joint where wood is simply glued on edges. A rabbet joint is cut halfway through a piece of wood, allowing glue to hold on both the ends and the sides of an adjoining piece. This strengthens the join slightly and also makes it easier to make square sides, bases and ends.

    Rabbet joints can be used to make a basic box, by cutting the rabbets on the base, gluing the sides to the base, then making a fitted top by cutting rabbets on the edges of a top piece and adding a handle.

    This project is designed to help you learn to file simple rabbet joints accurately. For that reason the rabbets are made on the box ends. Normally the rabbets would be made on the base, and or the decorative side edges, so that no joins are visible on the main sides. Here they are used on the box ends, as it makes for a bit less work while you practise making straight rabbets.

    Continue to 2 of 10 below.
  • 02 of 10

    Materials Needed to Make a Basic Box With Heart Cutouts in Dollhouse Scale

    Glue, wood, sandpaper, miniature files and drill to make a dollhouse windowbox.
    Materials to make a simple wooden storage or window display box in dolls house scale. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    To Make The Dollhouse Storage Box You Will Need:


    • Stripwood I used 1/2 inch by 1/16 inch basswood. Use harder woods if you can find them (jelutong, limewood, mahogany). The planter shown used 3 pieces cut 2 inches long for the sides and base, and two pieces cut 5/8 inch for the ends. If you want to store particular items in your box, make sure the box is wide enough and long enough on the inside to take them, you may need to use wider stock if you need a wider box.
    • Wood Glue You can use PVA...MORE (white glue) if you don't have wood glue, but wood glue will form a stronger, more watertight bond.
    • Craft Knife You need one with a fine tip for the cutout hearts.
    • Craft Saw or you can use a Stripwood Cutter
    • Miniature Drill The size of the drill bit will determine the size of the lobes of your hearts and the curve of the handle on the end of the box. Use one that is close to the size of the end of your round file.
    • Miniature FilesYou will need a straight sided flat file, a round or oval file, and a tapered flat file (a pointed metal nail file can be substituted for the flat file and the tapered file if necessary)
    • Sandpaper Use a fine grit, 220 or finer.
    • Glue Spreader or flat toothpick.
    • Wood Finish or Paint If you want to finish the wood for your box.


    Continue to 3 of 10 below.
  • 03 of 10

    Cut the Crate Handle Openings In the Box Ends

    A miniature drill cuts handle openings in a dolls house storage or window box.
    A miniature drill is used to cut holes along the line for an open handle in the end of a dolls house storage box. Flat and round files are then used to finish the cutout handle. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    Cut the Handle Openings in the Two End Sections of the dolls house crate

    Mark the Handle Location Take your two box ends and use a paper embosser, or a ballpoint pen, to mark the center of the handle for your crate ends. I set mine about 1/8 inch below the top edge. Set your drill on the mark to make sure you will leave enough wood above the handle for a secure edge. When you have the correct depth figured out, mark the wood at the center, and one drill bit width away on either side, so you have...MORE three centered marks to start your drill on. Your crate handle will be three drill bits in width.


    Drill Three Holes for the Handle Center your drill bit on your marks and use your drill to make three holes side by side. You have to be careful to avoid slipping the drill bit sideways.

    File the Handle Smooth Use your round and flat files to neaten the ends and the base and top of your handle slit. The round file will round the ends, and the flat file will make a straight edge on the top and bottom.

    Sand The Handle Edges Roll up a tiny piece of sandpaper, or roll it around a toothpick or wire, and use the sandpaper to smooth the ends of the handle opening. Take care to keep the slot straight across between the rounded ends.

    Continue to 4 of 10 below.
  • 04 of 10

    Cut The Rabbet Joints on the Ends of the Miniature Box

    A flat file cuts miniature rabbet joints are on the ends of a dolls house window box.
    A flat file is used on the inside edge of a dollhouse windowbox to form miniature rabbet joints to strengthen the box. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    Cut Miniature Rabbets

    Mark the joint edges Your rabbet joints will need to be 1/16 of an inch wide on the sides and bottom of the end of your box. This width of joint will allow you to fit your 1/16 inch wooden sides and base, neatly into the edge of the joint, helping to hold the pieces square for gluing. To mark the joints, measure 1/16 of an inch away from the side and base edges and mark the line with a shallow knife or saw cut.

    Cut the Rabbet To cut the rabbet, clamp your wood firmly with the...MORE inner edge of the crate end facing up. Line up the straight side edge of your miniature flat file with the measurement mark you made in the first step above, and carefully file back and forth on the outer edge of this mark, keeping your file straight and flat. This takes a little practise so stop often and check the edge of your work to see how your filing is progressing. You want to file a square flat section from the mark you made, halfway through the thickness of your end piece. Take short strokes with the file and clean the file by tapping it on your work surface to clear it of sawdust. It is handy to have a clean used toothbrush to clear out any sticking sawdust.

    Make Three Rabbets one for each side and one for the box base. When you get used to making these joints you can make rabbits on all four sides of the base, or the sides instead of on the ends of the box, but for now, it is easier to practise on shorter sides, which is why we are making the rabbet joints on the smallest side of the box. Rabbet joints hide the butt edge of the wood you glue to them, making a neater, slightly stronger finish than a butt joint.

    Check the fit of the joints by test fitting the sides and base of your box to the ends.

    Set the ends aside while you finish the decorative hearts on the sides in the next step

    Continue to 5 of 10 below.
  • 05 of 10

    Use a Drill and Files to Make Cutout Hearts In a Miniature Wooden Crate

    Use a drill, a craft knife and files to cut out heart shapes in the sides of a dollhouse windowbox.
    Use a small drill bit to cut holes for the tops of the heart cutouts, a craft knife to cut out the point of the heart, and round and flat files to finish the shapes of the hearts. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    An Easy Way to Make Cutouts in Wooden Miniatures

    Mark the Drill Holes To make heart cutouts for miniatures start by choosing a drill bit for the heart lobes at the top. Use a pen or a embossing tool to mark the starting hole for your drill and drill a single hole through the side of your box. When you have the first hole drilled, drill the second hole far enough away to one side of the first hole so that you leave the point of the heart at the top intact when you drill. You could use this...MORE technique to make shamrocks from three hearts that join together.

    Cut the Point of the Heart Use a fine craft knife to cut down from the outside edge of your drilled hole to the place you want the bottom point of your heart. Try to line your point up with the indent on the top of your heart between the two drill holes. Cut a matching line up from the point of the heart to the outside edge of the second drill hole at the top of your heart. Don't worry if your heart isn't heart shaped, files will neaten your cutout.

    Flat File the Point of the Heart Use the flat side of a miniature tapered file to straighten the point and the bottom edges of your heart. Try not to cut into the circular lobes at the top of the heart. If you do slip into the lobes, it can be fixed with the circular file.

    File the Top Lobes Use the circular or oblong file to round out the lobes at the top of your heart. Be careful to leave (or make) a point in the center of the heart top, between the two lobes. If you lost this point when you were drilling, just file your lobe further away from the center to make a new center indent.

    Sand the Heart Shape to get a finished edge on your cutout. Roll up a bit of sandpaper to sand the lobes of the heart and fold a strip to sand the straight point of the heart.

    Repeat on the Other Side If this is a window box, you can leave the back without cutouts.

    Continue to 6 of 10 below.
  • 06 of 10

    Test Fit the Parts of Your Miniature Box

    Sides, ends and base of a dolls house scale window box with heart cutouts, laid out for assembly.
    Sides, ends and base of a dolls house scale window box with heart cutouts, ready for assembly. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    With all your parts prepared, do a final test fit to make sure the joins line up properly. Make sure the ends of your pieces are straight and true. Check them with a square, or the end of a metal ruler. Sand the ends of the joints if necessary to square them up for gluing together.

    Continue to 7 of 10 below.
  • 07 of 10

    Glue the Base and One Side of the Box

    The side and base of the box are glued to the rabbets cut in the ends, and to each other.
    The side and base of the box are glued to the rabbets cut in the ends, and to each other. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    Spread a small amount of glue on the rabbets you cut in the end of your box. Spread a small amount of glue on one end of the base, and one side of the base. Press fit the base of your box into the rabbet on the end of the box.

    Run a small amount of glue on the end of the side that fits the box end, and press the side onto the rabbet on the end of the box, and up against the glued edge of the box base. The box base and the side will be glued in a simple butt joint, where one piece glues flat on...MORE it's end to the side of the other piece.

    Finish gluing the box by adding the final side onto the end and base. Then add glue to the other rabbets on the final end of the box and glue it to the sides and base.

    Carefully wipe away any excess glue that come out of the joint seams.

    See the next step for clamping the box.

    Continue to 8 of 10 below.
  • 08 of 10

    Clamping the Box To Strengthen the Joins.

    Clamps hold the sides and ends of a newly glued dollhouse window box against its base.
    Clamps are used to gently exert pressure on the joints of a newly glued dolls house window box. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    Glue joints are always stronger if the wood is clamped in place until the glue dries. To clamp a miniature box, small, quick release bar clamps are easiest to use. This box has three, two clamp the sides evenly to the base, and the ends, and a third clamps the box ends to the base and sides.

    If you don't have clamps you can use a gluing jig, like this magnetic one or use a straight piece of wood laid against the sides of the box, and hold those pieces of wood tight against the box with rubber...MORE bands or twist ties. If you use rubber bands, you may need a second person to hold everything square while you fit a rubber band. Do not try to use rubber bands directly on your miniature piece!

    Set the box aside until the glue dries.

    Continue to 9 of 10 below.
  • 09 of 10

    Final Sanding To Neaten the Edges

    A dolls house window box after its final sanding.
    The dolls house window box is given a final sanding after gluing to square the edges. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    When your box is dry, use fine grit sandpaper (220 or higher) and a square sanding block to neaten the edges of your box at the glued joins. The rabbets you cut should help to keep your box square, but you will still need to sand to make sure all the edges are even. You can see the rabbit joints on the end of the box in the photo above. After this practise run, try making a box with the rabbets on the base and the sides, to make a stronger, neater box for a window box. Don't expect your...MORE first attempt to be perfect. This is an easy way to make better wood joins than the butt joins commonly found in miniature furniture kits, but you need to get used to working with wood files.

    You can finish your box with a clear finish at this stage, or attach paper fruit crate labels or shop decals to the box and add a clear coat over them when they are dry.

    Continue to 10 of 10 below.
  • 10 of 10

    Adding a Crackle Finish to a Dolls House Crate or Window Box

    A dollhouse scale window box with heart cut outs on the sides finished in a purple crackle finish.
    A dolls house scale window box with heart cut outs on the sides finished in a scale crackle finish. Photo copyright 2009 Lesley Shepherd, Licensed to Inc.

    To add a crackle finish to my dollhouse window box I used Ranger Distress Crackle paints

    This paint is available in several colors, including white and metallics. It goes on very thick. For miniature crackles you may need to thin it a bit with water. If you want a color showing through the crackle, paint the crate with acrylic paint in your chosen color and allow it to dry completely before applying the crackly paint. The miniature crackle paint can be lightly sanded to further the weathering...MORE effect, but when you have the look you want, you may want to apply a clear matte or satin glaze over the crackle to help hold it in place. Otherwise handling may cause your paint to wear more than you wish.

    To set up the windowbox, I used reindeer moss behind the cutouts to give it a moss basket effect, and set the plants into a small piece of dry floral arranging foam cut to fit inside the box. The top surface of the foam has a layer of reindeer moss on top.