How to Make a Simple Open Loop with Wire

  • 01 of 05

    Simple Wire Loop Instructions

    Complete Eye Loop
    Completed eye pin loop. Lisa Yang

    Understanding how to make a simple wire loop is an important basic wire working skill. It can be used to make wire findings such as eye pins, loops to make bead dangles, or to make bead connectors for a rosary style bead chain.

    Practice is important to make the loops round, even sized and centered on the wire.

    Simple loops can be made with most types of wire depending on the purpose they will be used for.  For this example, I am using 20g half hard sterling silver filled wire.  Simple loops will...MORE be more secure if you use half hard wire rather than soft wire.

    Continue to 2 of 5 below.
  • 02 of 05

    Line Up Wire in Round Nose Plier

    Line Up Wire
    Line up your wire with the edge of the pliers - you should barely feel the edge when you run your finger over it. Lisa Yang

    Start with a piece of wire appropriate for what you are making.  To make an eye pin, a 1 1/2 or 2 inch piece of wire is a good size.

     In order to have a round loop, it is important that you start with you wire properly aligned inside the jaws of the plier.  Align it to the top edge between so the you can barely feel the edge of the wire if you pass your fingers over the top.

    If the wire pokes you when you rub your finger over the top, it is too far out.  If you can't feel the edge at all, it...MORE is too far down between the jaws of the plier.

    Note that I have already made a mark where I want to make my loop on the plier using a permanent marker.  This helps to make all of the loops approximately the same size.

    Continue to 3 of 5 below.
  • 03 of 05

    Wrap the Wire Around the Round Nose Plier

    Wrap Wire to Make Loop
    Wrap the wire around the plier to make a loop. Lisa Yang

     Wrap the wire around the round nose plier. You can do this by turning your pliers and rolling your wrist BUT you may strain your wrist if you do this motion repetitively.  I find it better and easier on my hands if I try to keep the hand holding the round nose plier still and use the other hand to push the wire around the barrel until it is wrapped as far around as it will go.

    Make sure the wire is pushed flat against the plier to get a perfectly circular loop.

    Continue to 4 of 5 below.
  • 04 of 05

    Reposition the Loop on the Plier and Finish the Loop

    Finish Simple Loop
    Reposition your pliers to finish wrapping the wire around the pliers and complete the loop. Lisa Yang

     In order to completely close the loop, reposition your pliers and make a final small turn so the cut wire end is flush with the edge of the main wire and forms a complete circle.

    Remove the loop from the plier and you will have a round circle loop but it will not be centered on the wire.  There is one final but very important step to centering the loop on the wire.

    Continue to 5 of 5 below.
  • 05 of 05

    Center the Loop on the Wire aka Break the Neck

    Break Neck of Loop
    Insert your pliers at the base of the eye loop to bend the loop back and center it on the pin. Lisa Yang

    The step to center the loop is often referred to as breaking the neck of the wire. It makes sense if you think about the wire loop as a head on the wire. You need to adjust the neck by making a bend at where the wire meets the loop so it can sit in the center.

    To do this, insert your round nose plier at the base of the loop and pull the wire away from the open end of the loop just a little. You can do this a little at a time to make sure you don't over adjust it. Once the loop is centered on...MORE the wire, your eye pin is done.

    You can make a bead connector by adding a bead and making another eye loop on the other side of the bead.

    If you find that it is difficult on your wrist or hands to make simple loops, or that you have diffculty making them an even size, you may find it easier to use a 1 step looper plier