Make Wire Leaf Charms

  • 01 of 07

    Wire Leaves

    DIY Gemstone and Wire Leaves Earrings
    Tourmaline Gemstone and Wire Leaves Earrings. Lisa Yang

     This pair of earrings uses the wire leaves from these instructions as dangles. Once you have learned to make this basic leaf shape, it is easy to make variations including a leaf with a center vein that you can add beads to.

    The tourmaline gemstone chain is made using a variation on the wire wrap loop technique to make a bead chain.  I call the variation a double wire wrap loop and it results in a slightly thicker wrap around the main wire.  It takes a little more wire but if you can make a wire...MORE wrap loop, you will find it easy to make a double wire wrap loop too.

    Continue to 2 of 7 below.
  • 02 of 07

    Simple Wire Leaf Frames

    Assorted Handmade Wire Leaves DIY
    Assorted Handmade Wire Leaves. Lisa Yang

    These simple wire leaves can be used in a lot of different ways in your jewelry designs. They can be used as frames to add beads to, as dangles on earrings, or a focal pendant.  They are very easy to make too - with just a few basic wire working tools.

    This step by step will show you how to make the pointy end leaves on the right in the picture. 

     To make wire leaves, you will need 20g or 22g wire. I am using 20g red brass wire - but this project will work equally well with copper, craft wire,...MORE sterling silver or gold filled wire.  The size of the wire is also variable depending on how large you would like your finished leaves to be.  The pictures in this project start with a piece of wire 3 inches long and make a leaf about 1 inch long.

    Continue to 3 of 7 below.
  • 03 of 07

    Materials and Tools to Make Wire Leaves

    Crease folded wire
    Press the wire fold firmly so it is creased. Lisa Yang

    You will need basic wireworking tools including chain nose pliers, round nose pliers, flush cutters. In addition, you will need something round to wrap the wires around. I use plastic step mandrels meant for jewelry making. They are so affordable and useful, I highly recommend them, but you can also use the barrel of a pen or marker. If you have a ring mandrel or step pliers, those may work as well.  It really depends on the size of the leaf you are making.

    Cut a piece of wire and mark the wire...MORE in the center. Fold the wire in half in the middle using your pliers.  If you didn't get it right in the center, you can trim the wire ends to make them even.

    Use your chain nose pliers to press the wire together in the center.  This is what will give the leaves a pointy end.  If you don't press the wires together, you will make a more rounded wire leaf.

    Continue to 4 of 7 below.
  • 04 of 07

    Shape the Wire Leaf

    Shape Wire Around Mandrel
    Shape the wire by wrapping it around a round mandrel. Lisa Yang

    Gently pull apart the wires so you have a deep V where they meet.  Wrap the wires around a mandrel and push the wires around the mandrel until they meet. You will usually need to shape it one more time around the mandrel, so just beginning to get the rounded sides at this point is fine.

    Continue to 5 of 7 below.
  • 05 of 07

    Initial Wire Leaf Shape

    Make wire leaves
    Shape the wire around a round mandrel to make leaf shape. Lisa Yang

    The initial wire leaf shape will resemble a stick fish figure (you know what I'm talking about right?).  Turn it to the side and you'll see.

    Continue to 6 of 7 below.
  • 06 of 07

    Add a Simple Loop on the Wire Ends

    Add loops to the end of the wire and re-shape the leaves
    Add loops to the end of the wire and re-shape the leaves. Lisa Yang

    Make a simple loop on each of the wire ends.  This is the loop that you will either hang the leaf by or add a jump ring to this loop. Plan the size of your loop accordingly. 

    Continue to 7 of 7 below.
  • 07 of 07

    Re-Shape the Leaf

    DIY Wire Leaves
    Completed wire leave is great for earrings or to embellish. Lisa Yang

     Re-shape your leaf around a round mandrel and push the two simple loops so they are aligned. Your leaf is done.  You can use a hammer to lightly hammer the sides and pointy end of the leaf shape.  Do not hammer the loops since they will probably get bent out of shape.