# Guide to Roof Pitch and Roofing Materials

When choosing roofing materials, it may seem that you have an infinite choice of any material on the market: asphalt, composite, metal, wood shake, rubber, and MSR rolled roofing. It's easy to imagine that the choice is purely an aesthetic or economic one: that you pick a roofing material according to what you like or what you can afford.

That's only partly true. Other factors determine which roofing materials you can use. One solid factor is the pitch of the roof, also known as the roof slope. Roof pitch can instantly change the conversation. You may have your heart set on classic composite shingles on your roof. But if the roof pitch is below a certain ratio, you may be forced to install a different type of roofing—perhaps rolled roofing or standing seam metal roofing.

## What Roof Pitch Is

Pitch describes the angle, slope, or slant of your roof.

Roof pitch designations are comprised of two numbers indicating a ratio. The ratio can be shown by a division slash separating the numbers, such as 2/12 or 7/12. Or, a colon can replace the slash, as in 2:12 or 7:12. Either way, the notation designates a ratio between two measurements of the roof—a numerator and denominator.

• Numerator: The numerator, or first number, refers to the vertical (height) measurement of the roof.
• Denominator: The denominator, or second number, denotes the horizontal (length) measurement of the roof. To make things a bit easier, for roofing purposes the denominator is always 12. Even though basic mathematics tells us that 12/12 can be reduced to 1/1, this is not done with a roof pitch. The denominator remains 12.

For example: A roof with a vertical measurement anywhere along its slope of two feet and a horizontal measurement of four feet has a 2:4 pitch. To adjust for roofing purposes, you would multiply the second number by three. The first number must be multiplied by three, too. The roof pitch, then, is 6:12.

## How to Calculate Roof Pitch

To determine your roof pitch, hold a level with one end resting on the roof. Lift the other end in the direction of the slope of the roof, with the end resting on the roof at a higher point than the end you're holding. Raise or lower the level until you get a level reading. Measure out one foot from the end that is touching the roof. Measure down from the one foot point to the roof. If it is four inches, you have a 4/12 pitch, and so forth.

## How to Calculate Roof Pitch From a Ratio

The pitch of a roof is nothing more than a ratio that indicates how much rise there is in the roof over a 12-unit horizontal distance.

### Example: Ratio of 5:12 or 5/12

When you see the ratio 5:12, this means that for every 12 horizontal feet, the roof changes 5 feet in vertical height.

### Example: Ratio of 8:12 or 8/12

When you see a ratio of 8:12, this means that for every 12 horizontal feet, the roof changes eight feet in vertical height.

For most home styles, roof pitches fall in a range 4/12 (a moderate) slope up to 8/12 (fairly steep). Examples of extreme slopes range from 1/4:12 (almost flat) to 12/12 (sloping down at a perfect 45-degree angle).

## Roof Pitches and Roofing Materials

### Very Low Roof Pitches: .25/12 to 3/12

Roof pitches with lower angles, such as 1/12 up to 3/12 are found in more urban, contemporary style houses and in industrial buildings and shacks. It was fashionable for modern-style homes built in the 1960s to have little pitch, just a barely negligible slope to help drain water. Visually, this roof appears flat. This pitch might be as low as 1/12. The flat roofing materials most appropriate to these shallow-sloped roofs include:

• Built-Up Roofing: Sometimes called tar-and-gravel, or BUR, the modern form of this kind of roof consists of alternating layers of bitumen and reinforcing fabrics.
• Torch-Down Roofing: This is a single layer membrane-style roofing material that is heat-activated by a torch during installation.
• Rubber Membrane: EPDM (short for ethylene propylene diene monomer) is a true rubber that can be applied to a roof with glue or mechanical anchors.
• Standing Seam Metal: These roofs are made from panels of aluminum or steel joined together in raised seams. They can be used on roofs with pitches as low as .25 /12. They are also used on much steeper roofs.

### Low Roof Pitches: 2.5/12 to 19/12

Clay or cement tiles can be used on a wide range of roof pitches. For pitches of 2.5/12 up to 4/12, the roof requires double underlayment. Slopes above 19/12 are not recommended since tiles on very steep roofs can rattle.

### Normal or Moderate Roof Pitches: 4/12 to 20/12

A great many residential roofs fall into this category. The roofing materials most often used for these pitches include asphalt (composite) shingles: Traditional 3-tab shingles made with asphalt composite are the most popular type of shingle and are the most flexible in terms of adapting to many roof pitches. These shingles are appropriate for pitches as low as 4/12 pitch, all the way up to a 12/12 pitch. Think of them as taking the middle road in terms of roof pitch—not too flat, not too steep.

### High Roof Pitches: 5/12 to 12/12

Wood and slate shingles are used in many of the same types of roofs as asphalt composite shingles but may not be appropriate for roofs near the lower end, since they are more susceptible to leaking. Wood and slate shingles do not lock together as tightly as other types of shingles.

### Very High Roof Pitches: 18/12

Roofs on Victorian-era houses were often sharply angled with a steep pitch. Think of an old house with its soaring peaks and you have a picture of a high-pitched roof. This is one of the rare pitches where the numerator is greater than the denominator, with a slope as high as 18/12.

## Roofing Materials at a Glance

Most roof materials have a recommended pitch range for which they are most appropriate. The rules can occasionally be broken, but generally, you should not exceed the low range of the recommendation.

For example, wood and slate shingles might work for roofs steeper than the top recommendation of 12/12, but you should not install them below the 4/12 lower range.

• Built-Up (BUR): .25/12 to 3/12
• Torch-down roofing: .25/12 to 3/12
• Rubber membrane: .25/12 to 3/12
• Standing-seam metal: 1/12 to 19/12
• Clay or cement tiles: 2.5/12 to 19/12
• Asphalt (composite) shingles: 4/12 to 20/12
• Wood and slate shingles: 5/12 to 12/12