How to Stop a Running Toilet and Prevent Overflow

Flushing toilet bowl landscape
Peter Dazeley / Getty Images
Overview
  • Working Time: 20 mins
  • Total Time: 20 mins
  • Skill Level: Beginner
  • Estimated Cost: $10-15

A constantly running toilet is a common problem in many homes, not to mention a major annoyance and a significant waster of water. Fortunately, addressing this issue is simple and will help you reduce your water usage. Rather than call out a plumber, these easy steps help you understand how to do it yourself with little hassle. Let's start with a simple lesson on toilet mechanics.

How a Toilet Works

A basic understanding of the mechanisms in your toilet and how they work will help you make the necessary repairs.

  • When you press the handle, a chain lifts a flap (called a flapper) that allows the water in your tank to flow into the bowl. As the tank empties, the flapper drops and closes the opening to begin the refill cycle.
  • A large plastic float drops as the water empties out of the tank. The float is connected to a float valve that opens when the float is down and closes when the tank is full and the float is up.
  • An overflow tube in the center of the tank drains excess water into the bowl if the level in the tank gets too high. This tube is also the channel through which the float valve sends water to the bowl during the refill cycle.

A constantly running toilet, or a toilet that tops up its tank by itself, can stem from a variety of issues, including a faulty flapper, a high water level, or a water-logged float. If none of these seem to be the problem, you probably have a broken valve. The best solution is simply to replace it.

What You'll Need

Equipment / Tools

  • Pliers
  • Bucket

Materials

  • New flapper kit
  • New flapper chain
  • New fill valve

Instructions

Troubleshoot a Faulty Flapper or Chain

Your toilet’s flapper is a plastic or rubber cap that keeps water in your tank. Over time, your flapper can become brittle and create a faulty seal. If your tank doesn’t refill or hold water, it’s likely due to a sub-par flapper.

  1. Check the Flapper's Consistency

    In many cases, flappers become hard and stop creating an adequate seal. Check the condition of the flapper by rubbing it between your fingers. You want it to feel soft. If rubbing it between your fingers turns your fingers black or leaves a black residue, it's time to replace the flapper.

  2. Examine the Chain

    Make sure the chain connected to your flapper isn’t catching on anything. If you have an overly long chain (with lots of extra hanging down), trim off some excess to prevent tangles. If the chain is rusty or isn't designed for this use, replace it with a new flapper chain.

  3. Ensure a Full Seal

    Flappers can become pinched in their hinges. Look for a side of the flapper that’s jammed and preventing a full seal.

  4. Adjust the Alignment

    Flappers can become dislodged and cause leaks. Make sure your flapper is seated directly over the drain.

Adjust the Water Level

Your toilet’s overflow tube ensures that the tank doesn’t overfill and flood your bathroom. But if the fill valve's float is set too high, small amounts of water will leak into the overflow tube and into the bowl, resulting in the fill valve turning on automatically and topping up the tank periodically.

  1. Lower the Float

    Lower the float setting on the fill valve. Some valves have a metal rod and a small clip that you squeeze to slide the clip (and float) up and down on the rod; move the clip down to lower the water level. If you have an old fill valve with a long rod and a tank ball, carefully bend the rod in the middle so the ball goes a little deeper into the tank.

    Tip

    Water-logged floats can also cause constant running. If water is trapped inside your float, it will sit lower in the water and leave your float valve partially open. Check your float by unscrewing it (if applicable) and shaking it. Replace the float if you hear water inside. 

  2. Let the Toilet Refill

    Flush the toilet and let it refill and stop by itself.

  3. Note the Water Level

    The water level should be about 1/2 to 1 inch below the top of the overflow tube.

  4. Adjust Again If Necessary

    Adjust the float more, if necessary, and flush again, until the refill stops at the proper level.

Replace the Fill Valve

Your fill valve controls the flow of water into your toilet’s tank. A broken valve may fail to shut off or may shut off inconsistently, leading to non-stop or unintended refill cycles. Submerged float valves are the most common sign of a faulty fill valve. Because fill valves are inexpensive and easy to replace, it's better to replace an old fill valve than to attempt a repair.

  1. Prepare the Toilet

    Turn off the water supply by closing the shutoff valve on the pipe leading to the toilet. Remove the tank lid. Flush the toilet to empty the tank.

  2. Disconnect the Supply Hose

    Place a plastic bin or bucket below the water supply hose. Disconnect the supply hose from the bottom of the fill valve.

  3. Remove the Old Fill Valve

    Remove the old fill valve by unscrewing the locking nut on the bottom of the water supply shank and pulling the entire valve assembly out of the tank. Residual water in the tank will drain into the bin or bucket.

  4. Install the New Fill Valve

    Adjust the height of the new valve to fit the height of the tank, following the manufacturer's directions. Insert the threaded end of the valve into the hole in the tank, and secure it with the locking nut, tightening by hand. Use pliers to turn the nut a bit further to create a watertight seal, but be careful not to over-tighten.

  5. Attach the Water Supply

    Attach the supply hose to the fill valve and tighten it snugly (not too tight) with pliers. Clip the valve's refill hose onto the top of the overflow tube so the hose points down into the tube. Most valves come with a clip or angle adapter that ensures the tube is at the right angle.

    Tip

    Avoid placing the tube below your water line. This will lead to constant refilling.

  6. Test Your Work

    Turn on the water at the shutoff valve. Let the tank refill. Fine-tune the water level, as needed, so the water stops about 1 inch below the top of the overflow tube, or as specified by the manufacturer. Replace the toilet tank’s lid. 

    1:53

    Watch Now: How to Replace a Toilet Flapper

      1:20

      Watch Now: How to Adjust a Toilet Fill Valve