How to Use a Snap on Adjustable Bias Tape Binding Foot

  • 01 of 03

    Adjustable Bias Tape Binding Foot

    Snap On Adjustable Bias tape Binding Foot. Debbie Colgrove, Licensed to

    I've been sewing bias tape for many years using the basic tools but I recently found this Snap on Adjustable Bias Tape Binding Foot sewing machine foot on for a couple of dollars and couldn't resist, even though I had never had this type of foot and had no idea if it would be worth while.

    The presser foot comes from China and because I did not pay to up-grade the shipping method it took many weeks for it to arrive. The foot was in a a small plastic bag inside a small bubble...MORE wrap envelope but came with no instructions. Learning how to use the foot is not a difficult process once you begin experimenting with the foot.

    The foot is designed to guide double fold bias tape so you can sew it straight and enclose a layer of fabric, such as for edging. This particular foot is a snap on presser foot. You will need the foot for your sewing machine if you choose to invest in this type if presser foot.

    Continue to 2 of 3 below.
  • 02 of 03

    Adjustments on the Snap on Adjustable Bias Tape Binding Foot

    Adjustments on an Adjustable Bias Tape Biinding Foot. Debbie Colgrove, Licensed to

    The foot has two adjustment locations. These points are marked with red arrows in the photo.  One is on the back, metal side of the foot which tightens and loosens by moving the screw clockwise and counter clockwise.  Once this screw is lose, the plastic part of the foot slides left and right and right to left. This screw can be carefully removed to work with just the plastic part of the foot. Be very careful not to lose the small washer if and when you separate the parts of the foot.  Once it...MORE is in the position you want, you must tighten the screw to keep the foot in place.

    The other adjustment is a knurled knob on the left hand side of the plastic part of the foot. This screws in and out, adjusting the "backstop" for the folded edge of the double fold bias tape. 

    Moving both adjustments as far out to the right is for use with wide double fold bias tape and adjustments to the left work best with narrow double fold bias tape. I did not manage to get the "backstop" far enough over to the right for the purchased narrow double fold bias tape.

    Once the backstop is adjusted, the edges of the bias tape that you will be sewing, should be in the upper and lower "lip" edges of the plastic part of the foot.

    Continue to 3 of 3 below.
  • 03 of 03

    How to Use An Adjustable Bias Tape Binding Foot

    Attaching Bias Tape with an Adjustable Bias Tape Binding Foot. Debbie Colgrove, Licensed to

    The top of the plastic part of the foot does separate which seemed like it would allow for fabric or the bias tape to be held. When I attempted to feed the tape into the foot through the foot and the top plastic piece with the edges of the tape into the curled edges of the foot, the tape did not feed smoothly through the foot. Adjusting the "backstop" via the bottom screw adjustment allows the tape to feed through and helps guide the tape so it stays where it belongs in the...MORE "lips" of the foot. The top part of the plastic, which also has numbers on it, is purely for a guide to set the "backstop".  Preventing Sewing Machine Damage - Let the Feed Dog do the Work

    I found it easiest to set the plastic part of the foot and start the tape through the foot by un-attaching the plastic part from the metal part of the foot. You may also want to adjust your needle position in order to stitch closely to the edge of the bias tape.

    As with any sewing, watching a guide and not the needle is imperative to sewing straight. While sewing with this foot, I found I needed to watch the location of the edge of the bias tape that would be sewn and occasionally use a straight pin to guide the edge of the tape back in to the lip of the foot, especially when I was sewing the narrow bias tape because the back stop does not adjust far enough to hold it in place.

    Looking carefully at the photo, you can see that the "backstop" (yellow arrow)  behind the fold of the bias tape is adjusted for the width of the folded bias tape but that the back stop did not move all the way over to the fold for the red, narrow bias tape.

    I did make a sample of quilted fabric, using one layer of light weight cotton batting between two pieces of cotton fabric to test the foot binding quilted fabric. The sample was two thick for the foot. The quilted sample and the bias tape did not fit in the foot.  I would not buy this foot to bind quilted materials and I do not recommend attempting to bind quilted or layers of fabric as the opening in the foot is not large enough to handle even thin layers of fabric.

    Over all, the price of the foot made it a good investment but I am not sure that I would set this up to do small tasks. Perhaps if I were binding something like a BBQ apron it would be worthwhile but I would revert to my tried and true methods I have used for years for small projects.