Making Milk Soap Using Heavy Whipping Cream

  • 01 of 15

    How to Make a "Milk Soap" with Heavy Whipping Cream

    set up for heavy cream milk soap
    Setup, ingredients and tools for making milk soap with heavy cream. David Fisher

    Soap's made with milk are rich, creamy and extra moisturizing. Part of this comes from the extra fat in the milk, and part comes from the additional proteins and ingredients in the milk itself. There are a couple of preparation steps you need to take in order to best make milk soaps - and a few different methods for incorporating milk into your soap.


    You can:


    1. Use the milk in place of the water when making your lye solution
    2. Use half water and half milk in the recipe - making your lye solution with...MORE the half water, and adding the milk to the oils
    3. Use powdered milk added at trace

    For more information about these three methods check out:
    Making Soap with Goat's Milk (The procedure is mostly the same with any kind of milk.)
    Making Goat's Milk Soap Video


    I had a quart of heavy cream that I wasn't going to use for cooking, so decided to use it in soap. I used methods #1 and #2 to make the soap.


    You can add milk to any soap making recipe by just incorporating the milk in one of the three methods above. The recipe I used was:


    • 27% palm oil
    • 27% coconut oil
    • 27% olive oil
    • 5% castor oil
    • 14% almond oil

    The actual recipe to make a 2 lb. batch of soap was:


    • 5.3 oz. palm oil
    • 5.3 oz. coconut oil
    • 5.3 oz. olive oil
    • 1 oz. castor oil
    • 2.75 oz. almond oil
    • 2.9 oz. lye
    • 5.8 oz. water
    • .9 oz. fragrance oil

    Important Note: When you are calculating a recipe using heavy or whipping cream, be sure to take into account, or at least be aware of the extra fat content in the cream. Heavy cream has 36% milk fat in it, as compared to 4-6% fat in goat's or cow's milk. You may want to adjust your recipe to allow for that extra fat. I cover two ways to do this on the last page of this tutorial - or jump right there now.


    Continue to 2 of 15 below.
  • 02 of 15

    Freeze the Cream Ahead of Time

    frozen heavy whipping cream cubes for milk soap
    Frozen heavy whipping cream cubes for milk soap. David Fisher

    To get started with method #1 (using the milk in place of water in the lye solution), you're going to need the cream to be frozen. - so freeze the heavy cream (or whatever milk you're using) in an ice tray. While that's freezing, we'll move on to method #2, which is using a double strength lye solution, and adding the cream directly to the oils.


    Continue to 3 of 15 below.
  • 03 of 15

    Method #2 - Making a Double Strength Lye Solution

    making extra strength lye solution
    Making extra strength lye solution. David Fisher

    For method #2, we're going to make a double strength lye solution.


    My recipe called for 5.8 ounces of water and 2.9 ounces of lye. I divided the 5.8 ounces of water into 2.9 ounces of water and 2.9 ounces of milk.


    Using just the 2.9 ounces of water and 2.9 ounces of lye, I made the extra strength lye solution and set it (safely) aside to cool.


    Continue to 4 of 15 below.
  • 04 of 15

    Weighing out the Frozen Cream

    weigh out the heavy cream cubes
    Weigh out the heavy cream cubes. David Fisher

    I then measured out 2.8 ounces of the cream. (Note: If you're using method #2 and adding the milk/cream directly to the oils, the milk/cream really doesn't have to be frozen - but it is more convenient to measure and store it this way.)


    Continue to 5 of 15 below.
  • 05 of 15

    Adding the Cream to the Oils

    adding cream to melted oils
    Adding cream to melted oils. David Fisher

    Measure out and melt your oils like you would in any other batch of soap. When they are fully melted, add the cream (liquid or frozen) to the warmed oils.


    Continue to 6 of 15 below.
  • 06 of 15

    Blend the Cream into the Melted Oils

    blending the cream into the melted oils
    Blending the cream into the melted oils. David Fisher

    Blend the cream into your melted oils using your stick blender. You're not trying to reach any sort of trace or anything. It's just good mixing of the ingredients.


    Continue to 7 of 15 below.
  • 07 of 15

    Mix the Lye into the Cream/Oil Mixture

    Adding the extra strength lye solution to the cream and oil mixture
    Adding the extra strength lye solution to the cream and oil mixture. David Fisher

    Like you would any other soap batch, slowly and carefully pour the extra strength lye solution into the melted oils and cream. Blend it with your stick blender until you get a light trace. Add fragrance and/or color after you get to a light trace and pour it into your mold.


    Continue to 8 of 15 below.
  • 08 of 15

    Poured Soap (Using Method #2) In the Mold

    poured soap in mold
    Poured soap in mold. David Fisher

    As you can see, the soap got a good thick trace but is otherwise nice and smooth. (The fragrance oil gave it a little bit of a beige color in this batch.)


    Set the soap aside and unmold/cut it in about 24 hours.


    Continue to 9 of 15 below.
  • 09 of 15

    Method #1 - Making the Soap with Full Milk

    adding lye to cream cubes in pitcher in sink
    Adding lye to cream cubes in pitcher in sink. David Fisher

    Now, back to method #1.


    Take the full amount of water that your recipe calls for and measure out that amount in cream cubes. Put them in your lye pitcher in a couple of inches of cold water in the sink. Then slowly add the lye to the cubes a tiny bit at a time.


    Add a little lye - stir a little - wait a couple minutes.


    Add a little lye - stir a little - wait a couple minutes.


    Add a little lye - stir a little - wait a couple minutes.


    For a video demonstration of this, watch my ​Making Goat's Milk...MORE Soap Video


    Continue to 10 of 15 below.
  • 10 of 15

    Stir into a Lye & Milk Slush

    stirring and adding more lye bit by bit
    Stirring and add more lye bit by bit. David Fisher

    The heat from the lye reaction will melt the ice cubes. When all of the lye is added, you'll have a lye and cream slush.


    Continue to 11 of 15 below.
  • 11 of 15

    Cream Slush Thickening Up

    glob of lye and heavy cream
    Glob of lye and heavy cream. David Fisher

    Here is one part where using the heavy cream will be somewhat different than goat's milk. Because the fat content of heavy cream is so much higher than goat's milk (36% vs. 4-6%) the fat in the milk is going to start to saponify and turn into soap in the lye pitcher. It's going to get very thick - more of a lye-cream glob rather than a slush like goat's milk.


    Continue to 12 of 15 below.
  • 12 of 15

    Add the Lye-Cream Mixture to the Oils

    adding the lye-cream mixture to the melted oils
    Adding the lye-cream mixture to the melted oils. David Fisher

    Scoop out the lye-cream mixture and add it to your melted oils. Take a few tablespoons of water and use it to make sure that you've gotten all of the lye-cream mixture out of the pitcher and into the pot with the oils.


    Continue to 13 of 15 below.
  • 13 of 15

    Blend the Lye-Cream Mixture in with the Oils

    blending soap and squishing chunks
    Blending soap and squishing chunks. David Fisher

    Before you start stick blending, just make sure that the lye-cream mixture has fully dissolved and mash out any big chunks. Then stick blend the mixture like you would any other batch of soap.


    Add fragrance and/or color at trace and pour it into the mold.


    Continue to 14 of 15 below.
  • 14 of 15

    Thick & Grainy Soap in the Mold

    poured soap in mold
    Poured soap in mold. David Fisher

    This batch ended up being really thick and kind of "grainy" from the heavy cream. I blended it as best I could - and then poured it into the mold. You can see the difference in how thick this batch was from the soap I made with the 50:50 blend of water and cream.


    Continue to 15 of 15 below.
  • 15 of 15

    Finished Heavy Cream Soaps & Tips

    Finished soaps made with heavy cream. David Fisher

    Here are the finished soaps about 1 week after unmolding.


    The method #1 soap is on the left - you can see it's not as smooth as the method #2 batch. The color difference is from the fragrance oil - both batches were about the same color before I added the fragrance.


    Which method works better? They both work equally well, but I must admit, method #2 works better for me, especially with super high-fat content milk like heavy cream - you get a smoother pour and a smoother final soap.


    Another important...MORE note: When calculating a recipe with heavy cream, it helps to keep in mind the fat content of the cream. Heavy cream has a lot more fat than other milk - upwards of 30-36% vs. 4-5% in goat's milk. The fat in the goat's milk doesn't throw the superfat % off by very much - but the heavy cream can. If I calculated my recipe normally with a 5% lye discount and used the heavy cream in place of 100% of the water (method #1), I would increase my superfat to about 14%. If I used the 50% water 50% milk (method #2) I increase the superfat to about 9%.


    Part of what traditionally makes milk soaps more moisturizing and gentle is that extra superfat. But if those percentages are too high for you (Susan Miller Cavitch would love them!), here are two ways to compensate for the extra fat:


    1. Calculate your original recipe using a 0% superfat - knowing that the cream is going to add several % by itself
    2. Calculate the actual amount of fat you are adding to the recipe via the cream, and add that fat into the lye calculation. For example - in method #1, using 5.8 ounces of cream with a 36% fat content, I added just under 2.1 ounces of milk fat to the recipe. (5.8 X .36 = 2.088). I then added 2.1 ounces of milkfat into my lye calculator - and left the lye discount at 5%.

    Both methods of calculation work fine - and making no adjustment to the recipe is fine too, although a 14% superfatted soap is going to be more prone to spoiling over time. Obviously, option #2 takes a lot more math and calculation, but it is a way to really accurately keep your superfat/lye discount consistent with the rest of your soaps.


    Regardless of whether you use method #1 or method #2 - and whether or not you adjust for the fat content, you'll find that your soaps made with heavy cream are rich, creamy and luxurious - and still lather well too.